 |
BG |
Loop Box
The stand-alone Loop Box is a revolutionary new way to collect split times. At nearby split timing points detections are repeated wirelessly to the main system. In case of remote timing points, the ActivePro Transponder saves the passing time and then transmits them when arriving at the finish.
The Loop Box can be operated in Store Mode or Repeat Mode:
Store Mode
The ActivePro V3 saves up to 64 split times in Store Mode and transmits them at the next timing system:
Repeat Mode
If the split point is within 500 meters of the main timing system, all timing data is transmitted in real-time wirelessly from the Loop Box to Ubidium. The Repeat Mode is the smartest solution for triathlon transition zones:
Easy setup
No wiring needed between main system and split timing points
Stand-alone
With its internal battery the Loop Box can run for 12-20 hours.
3.5 mm input-/output-plug
Audio output or start impulse input
Repeat mode range
up to 900 m
Small investment
For an additional timing point you only need a Loop Box instead of a complete timing system.
| Safety & conditions Loop Box | |
| Protection class with cable / antenna screwed on |
IP52 -water resistant- IP54 (usage with Bumper) |
| Regulatory conformity | CE, RoHS, FCC |
| Temperature | -30°C to 70°C |
| Dimensions / weight | 27 x 66 x 117 mm / 272 g |
| Loop Box | |
| Maximum repeat range | Up to 900 m with direct line of sight |
| Passings transmission | Up to 40/second continuously |
| Passing transmission delay | 200 ms – compensated |
| Internal data buffer | 1,000 passings |
| Power & battery | |
| AC power supply Loop Box V2 |
110 V-230 V 50-60 Hz (2 A fuse) |
| Battery | LiPo, 4,000 mAh, 3.7 V 12-20 h depending on loop power |
Helpful Articles in our Knowledge Base:
Loop Box modes →
Loop Box configuration →
Setup of the timing line / loop cable →
Chip2Go
Produce your own UHF timing transponders! Enter the bib number via touchscreen, numpad or barcode scanner - Chip2Go encodes a transponder and feeds it out, ready to be attached to the bib. Chip2Go facilitates your job as a timer and can save you money.
Chip2Go is a device to program numbers to RACE RESULT Raw-Transponders. Wherever, whenever and as many as you like!
Specifications
- 3,4" sunlight readable display
- USB numpad included
- 15 V power supply included
- 12 V powering possible
- weight: approx. 5 kg
- USB ports for data import and firmware update
Operation Modes
- encode single or duo transponders
- enter number via touchscreen/ numpad/ optional barcode scanner
- increasing/ decreasing number range
| General | |
| Size | 25 x 23 x 21 cm |
| Weight | 4,60 kg (without accessories) |
| Temperature | -15°C to 45°C for use -25°C to 65°C for storage |
| Frequencies | UHF Gen2 866/915MHz |
| Output power | <16dBm |
| USB ratings | 3x USB 2.0 (500mA max. each) |
| Encoding speed | Up to 60 transponders per minute |
| Data input options | - 3.4" sunlight readable touch display - Numeric keypad — USB barcode scanner (optional) - Chip file from USB stick - Individual increasing/ decreasing number range |
| Delivery includes | - Chip2Go - Power supply - Numeric keypad |
| Power Supply | |
| Included |
- IN: 100−240V, 1.2A max. - OUT: 15V, 3.34A |
| Other options |
- 11−15V on a barrel jack, ID 2.00mm, OD 5.50mm - Compatible with Active System/Track Box power supply - Accepts supply from 12V car battery - Reduced Transponder feeding speed on input lower than 15V |
Helpful Articles in our Knowledge Base:
Device Setup →
Transponder Number Entry →
Cleaning Instructions →
USB Timing Box
The USB timing box is the handy alternative to the Active System. It is connected directly to the PC and does not need a Decoder. Thanks to the internal memory battery, 100 % reliable timing can still be maintained if the computer should fail. The USB Timing Box can be combined with loop boxes.
Directly connected to a computer, the USB Timing Box is a complete timing system and does not require a decoder.
The USB Timing Box is used best to time sporting events, to scan tags at race pack pick-up, or for just about any other application. The open-source software of the USB Box allows you to develop any solution that may have nothing to do with sports timing.
| 2.4 GHz RF & loop specification | |
| Transponder 2.4 GHz channel frequenciesmain / backup (worldwide compliance) |
1: 2.480 MHz / 2.405 MHz 2: 2.405 MHz / 2.470 MHz 3: 2.425 MHz / 2.465 MHz 4: 2.475 MHz / 2.440 MHz 5: 2.415 MHz / 2.445 MHz 6: 2.460 MHz / 2.430 MHz 7: 2.435 MHz / 2.455 MHz 8: 2.450 MHz / 2.420 MHz |
| 2.4 GHz TX power | 17.5 dBm |
| Loop frequency & data | 125 kHz data-packet = Loop ID + channel packet rate: 150 Hz OOK-modulation, manchester encoded, 16bit anti-false-wakeup pattern |
| Loop length | 5 m - 25 m, >0.5 mm²standard 4 mm banana plugs |
| Internal data buffer | 1,000 transponders |
| Read range 25% Loop power 100% Loop power | 60 cm (2 ft) 2 m (6 ft) |
| Detection rate Read rate | 100% > 250 chips/second burst for 4 seconds > 50 chips/second continuously |
| Battery | LiPo, 4,000 mAh, 3.7 V 12 hours |
| USB 1.1 | 500 mA |
| Safety & conditions USB Timing Box | |
| Protection class with cable / antenna screwed on |
IP67 -waterproof |
| Regulatory conformity | CE, RoHS, FCC |
| Temperature | -30 °C – 70 °C |
| Dimensions / weight | 27 x 66 x 117 mm / 266 g |
Helpful Articles in our Knowledge Base:
USB Timing Box Modes →
Display Explanation →
Setup of the timing line/ loop cable →
Management Box
The Management Box is a key component of the tracking solution, as it is required to activate and deactivate tracking on V2 transponders, as well as to manage your Track Boxes.
It also allows you to easily check your inventory of transponders, to generate chip files and to set the transponders to Deep Sleep Mode.
Please note, that this device cannot be used for race timing itself!
*In Deep Sleep Mode, the ActivePro and MotorKart transponders need 40% less energy, which can increase their lifetime by up to 30%.
| 2.4 GHz RF & loop specification | |
| Transponder 2.4 GHz channel frequencies(worldwide compliance) |
1: 2.480 MHz / 2.405 MHz 2: 2.405 MHz / 2.470 MHz 3: 2.425 MHz / 2.465 MHz 4: 2.475 MHz / 2.440 MHz 5: 2.415 MHz / 2.445 MHz 6: 2.460 MHz / 2.430 MHz 7: 2.435 MHz / 2.455 MHz 8: 2.450 MHz / 2.420 MHz |
| 2.4 GHz TX power | 17.5 dBm |
| Loop frequency & data | 125 kHz data-packet = Loop ID + channel packet rate: 150 Hz OOK-modulation, manchester encoded, 16bit anti-false-wakeup pattern |
| Loop length | 5 m - 25 m, >0.5 mm²standard 4 mm banana plugs |
| Internal data buffer | 1,000 transponders |
| Read range 25% Loop power 100% Loop power | 60 cm (2 ft) 2 m (6 ft) |
| Detection rate Read rate | 100% > 250 chips/second burst for 4 seconds > 50 chips/second continuously |
| Battery | LiPo, 4,000 mAh, 3.7 V 12 hours |
| USB 1.1 | 500 mA |
| Safety & conditions Management Box | |
| Protection class with cable / antenna screwed on |
IP67 -waterproof- |
| Regulatory conformity | CE, RoHS, FCC |
| Temperature | -30°C to 70°C |
| Dimensions / weight | 27 x 66 x 117 mm / 274 g |
