🗙
Filter equipment:

Loop Box

The stand-alone Loop Box is a revolutionary new way to collect split times. At nearby split timing points detections are repeated wirelessly to the main system. In case of remote timing points, the ActivePro Transponder saves the passing time and then transmits them when arriving at the finish.

The Loop Box can be operated in Store Mode or Repeat Mode:

Store Mode
The ActivePro V3 saves up to 64 split times in Store Mode and transmits them at the next timing system:

Repeat Mode
If the split point is within 500 meters of the main timing system, all timing data is transmitted in real-time wirelessly from the Loop Box to Ubidium. The Repeat Mode is the smartest solution for triathlon transition zones:

Easy setup

No wiring needed between main system and split timing points

Stand-alone

With its internal battery the Loop Box can run for 12-20 hours.

3.5 mm input-/output-plug

Audio output or start impulse input

Repeat mode range

up to 900 m

Small investment

For an additional timing point you only need a Loop Box instead of a complete timing system.

Safety & conditions Loop Box
Protection class with cable / antenna screwed on IP52 -water resistant-
IP54 (usage with Bumper)
Safety norm EN60950
Regulatory conformity CE, RoHS, FCC
Temperature -30°C to 70°C
Dimensions / weight 27 x 66 x 117 mm / 272 g
Loop Box
Maximum repeat range Up to 900 m with direct line of sight
Passings transmission Up to 40/second continuously
Passing transmission delay 200 ms – compensated
Internal data buffer 1,000 passings
Power & battery
AC power supply
Loop Box V2
110 V-230 V
50-60 Hz (2 A fuse)
Battery LiPo, 4,000 mAh, 3.7 V
12-20 h
depending on loop power

Chip2Go

Produce your own UHF timing transponders! Enter the bib number via touchscreen, numpad or barcode scanner - Chip2Go encodes a transponder and feeds it out, ready to be attached to the bib. Chip2Go facilitates your job as a timer and can save you money.

Chip2Go is a device to program numbers to RACE RESULT Raw-Transponders. Wherever, whenever and as many as you like!

short-term bib production on site
throw away less transponders
no separate chip file required
easy to handle, also for volunteers
error-free assignment of transponder to start number
self-sufficient process, without computer

Specifications

  • 3,4" sunlight readable display
  • USB numpad included
  • 15 V power supply included
  • 12 V powering possible
  • weight: approx. 5 kg
  • USB ports for data import and firmware update

Operation Modes

  • encode single or duo transponders
  • enter number via touchscreen/ numpad/ optional barcode scanner
  • increasing/ decreasing number range
General
Size 25 x 23 x 21 cm
Weight 4,60 kg (without accessories)
Temperature -15°C to 45°C for use
-25°C to 65°C for storage
Frequencies UHF Gen2 866/915MHz
Output power <16dBm
USB ratings 3x USB 2.0
(500mA max. each)
Encoding speed Up to 60 transponders per minute
Data input options - 3.4" sunlight readable touch display
- Numeric keypad — USB barcode scanner (optional)
- Chip file from USB stick
- Individual increasing/ decreasing number range
Delivery includes - Chip2Go
- Power supply
- Numeric keypad
Power Supply
Included - IN: 100−240V, 1.2A max.
- OUT: 15V, 3.34A
Other options - 11−15V on a barrel jack, ID 2.00mm, OD 5.50mm
- Compatible with Active System/Track Box power supply
- Accepts supply from 12V car battery
- Reduced Transponder feeding speed on input lower than 15V

Chip2Go :: Datasheet

Features and Technical Specifications

Chip2Go :: Quick Start Guide

Step-by-step instructions for newbies

USB Timing Box

The USB timing box is the handy alternative to the Active System. It is connected directly to the PC and does not need a Decoder. Thanks to the internal memory battery, 100 % reliable timing can still be maintained if the computer should fail. The USB Timing Box can be combined with loop boxes.

Directly connected to a computer, the USB Timing Box is a complete timing system and does not require a decoder.
The USB Timing Box is used best to time sporting events, to scan tags at race pack pick-up, or for just about any other application. The open-source software of the USB Box allows you to develop any solution that may have nothing to do with sports timing.

Wireless reception of split times from a Loop Box
Highest clock stability on the market: 0.28 ppm
100 % detection rate
Open Software Development Kit
1000 detection internal memory
Internal backup battery for 12 h
Compatible with all RACE RESULT active devices
1/1000th Data Resolution, Accuracy depending on Transponder Type
Works with low end computers
Loop power can be set by user
2.4 GHz RF & loop specification
Transponder 2.4 GHz channel frequencies
main / backup (worldwide compliance)
1: 2.480 MHz / 2.405 MHz
2: 2.405 MHz / 2.470 MHz
3: 2.425 MHz / 2.465 MHz
4: 2.475 MHz / 2.440 MHz
5: 2.415 MHz / 2.445 MHz
6: 2.460 MHz / 2.430 MHz
7: 2.435 MHz / 2.455 MHz
8: 2.450 MHz / 2.420 MHz
2.4 GHz TX power 17.5 dBm
Loop frequency & data 125 kHz
data-packet = Loop ID + channel
packet rate: 150 Hz
OOK-modulation, manchester encoded, 16bit anti-false-wakeup pattern
Loop length 5 m - 25 m, >0.5 mm²
standard 4 mm banana plugs
Internal data buffer 1,000 transponders
Read range
25% Loop power
100% Loop power

60 cm (2 ft)
2 m (6 ft)
Detection rate

Read rate
100%
> 250 chips/second burst for 4 seconds
> 50 chips/second continuously
Battery LiPo, 4,000 mAh, 3.7 V
12 hours
USB 1.1 500 mA
Safety & conditions USB Timing Box
Protection class with cable / antenna screwed on IP67
-waterproof
Safety norm EN60950
Regulatory conformity CE, RoHS, FCC
Temperature -30 °C – 70 °C
Dimensions / weight 27 x 66 x 117 mm / 266 g

Management Box

The Management Box is a key component of the tracking solution, as it is required to activate and deactivate tracking on V2 transponders, as well as to manage your Track Boxes.
It also allows you to easily check your inventory of transponders, to generate chip files and to set the transponders to Deep Sleep Mode.

Please note, that this device cannot be used for race timing itself!

Activate and deactivate tracking
Set transponders to deep sleep mode*
Generate chip files
USB connection
Manage Track Boxes
Keep track of transponder battery status
Scan trays to check

*In Deep Sleep Mode, the ActivePro and MotorKart transponders need 40% less energy, which can increase their lifetime by up to 30%.

2.4 GHz RF & loop specification
Transponder 2.4 GHz channel frequencies
(worldwide compliance)
1: 2.480 MHz / 2.405 MHz
2: 2.405 MHz / 2.470 MHz
3: 2.425 MHz / 2.465 MHz
4: 2.475 MHz / 2.440 MHz
5: 2.415 MHz / 2.445 MHz
6: 2.460 MHz / 2.430 MHz
7: 2.435 MHz / 2.455 MHz
8: 2.450 MHz / 2.420 MHz
2.4 GHz TX power 17.5 dBm
Loop frequency & data 125 kHz
data-packet = Loop ID + channel
packet rate: 150 Hz
OOK-modulation, manchester encoded, 16bit anti-false-wakeup pattern
Loop length 5 m - 25 m, >0.5 mm²
standard 4 mm banana plugs
Internal data buffer 1,000 transponders
Read range
25% Loop power
100% Loop power

60 cm (2 ft)
2 m (6 ft)
Detection rate

Read rate
100%
> 250 chips/second burst for 4 seconds
> 50 chips/second continuously
Battery LiPo, 4,000 mAh, 3.7 V
12 hours
USB 1.1 500 mA
Safety & conditions Management Box
Protection class with cable / antenna screwed on IP67
-waterproof-
Safety norm EN60950
Regulatory conformity CE, RoHS, FCC
Temperature -30°C to 70°C
Dimensions / weight 27 x 66 x 117 mm / 274 g
×

...may we help?

Get in touch quickly and easily now.

Contact us!


I have read the data privacy terms.